Sunshade’s panoramic sunroof replacement VW Audi Skoda Seat

Torn store? Relaxed? musty, dampness on the canvas? The spring is out of side guides?
We’ll see how to make sunshade’s panoramic sunroof replacement on VW Tiguan, Touran, Sharan, Golf V break, Audi Q5, Skoda Superb break, Skoda Yeti and Seat Leon break.
This is not given in concession because there is quite a labor the bill can easily go up to around 700€ or even much more.
It is a method that works, it is not the only one but i will give you all you need for sunshade’s panoramic sunroof replacement.

SAFETY – PRECAUTION

I disclaim any responsibility for any personal injury or damage to your vehicle. Please take the necessary precautions and check that you have not broken or damaged anything. If this is the case, then replace what was damaged before reassembly.

Check the electrical cables, some of which supply the airbags, so you don’t have to joke with safety organs.

Tools

• Torx T15 T20 T25 key/turntable or tip
• 10 key or tip (depending on model)
• Big flat screwdriver
• Dismantling tool available here (optional)
• Plastic dismantling tools to avoid scratches on the interiors of your car. Failing that, an old loyalty card, a guitar metronome etc…
• 6-pans key set or tip
• A new Sunshade you can find here

Time

5 hours depending on your skill level, this can be difficult for a novice.

Note: There may be some differences in the level of disassembly of the mounts depending on the models and the vehicles below:

VW SHARAN, TOURAN, JETTA, GOLF VARIANT, TIGUAN, AUDI Q5, SKODA YETI

For example: for the Golf Variant, the boot has to be disassembled in addition and the roof support is different, I deliberately omitted it because this car is rare. Whatever it is, you have enough information to successfully change the blind, curtain of the sunroof

1 – Open the sunroof in « maintenance position »

Open the TOP in maintenance position, if you don’t know how to do it you can read the article that features the VW panoramic sunroof by clicking here

the important thing is to have access to the screw that we see (position beyond the max)

2 – Open the sunroof blind to the maximum

4 – Disconnect the battery

As a safety precaution, it is advisable to disconnect the battery.

5 – Remove ceiling lights and plastic caches

Remove the plastic part using a pick and then remove the screws.

6 – Remove the left front side mount

Remove the AIRBAG symbol with the thinnest plastic tooling possible (pick) by leveraging by putting pressure on the shapes (see arrows inwards).
Do the same for the right front amount.

7 – Remove left center mount

You must start by removing the AIRBAG symbol as previously remove the fastening screw (put the belt setting high enough but not too high in order to be able to access with the torx screwdriver).

The amount must be detached from the lower dwellings in order to be able to bring it down (try not to take out the plastic part that serves as a setting for the height of the belt).
Do the same for the right.

8 – Remove the profile that goes around the roof sky

There are about twenty staples to de-clip by leveraging with a plastic disassembly tool (failing that you can use a blue card for example or a pick).

9 – Remove sunscreen

Open small caches with an extra fine plastic tool or a precision screwdriver but with caution, an extra fine guitar pick can do the trick.

Be careful with the sundness because it still holds by its cables so you have to remove the plug so that it is finally free.

10 – Remove the tailgate back cover (chest)

Open the tailgate and pull down the back cover with a snap.

11 – Remove the back cover (chest)

Remove plastic pushers with a special T10236 tool or with pliers on either side of the plastic part.

Remove the plastic part from the metal hoops then remove it upwards.

12 – Remove side cover (chest)

Motto the screws of the fasteners of the side part of the trunk then unseal the peripheral parts by passing the hands or a tool between the joint and the plastic.

13 – Remove top side cover (chest)

Remove the dressing piece by pulling down.

Shoot following arrows A and then B.

14 – Fold the back seat, advance the seats to the max and lower the seats

15 – Unplug plugs controls sunroof

16 – Remove plastic holding parts from roof sky

Remove the screws from the plastic part.

17 – Remove the handles

Take the handle as if you wanted to catch it remove the 2 torx screws.

 These are plastic parts to remove. The tool can be a bent screwdriver or a flat iron bent, or a toothpick that you will sew to pull perpendicularly

18 – Check that nothing holds the roof sky, light, ceiling light then extract the roof sky mold by advancing it forward in order to clear it from the rear studs and then extract the roof sky molded from the rear

19 – Remove the rear window from the sunroof

Deflect the screws (torx T25) from the top, paying attention to the 2 or 1 washers depending on the thickness of the washer that are on top.

If this is not already done, the mobile part of the sunroof should be brought back to the open position max. (by reconnecting the connector)

If you have to operate the sunroof you can do it manually with a 6-panel key directly on the sunroof engine in front

Lift the seal with your hands to pass the screwdriver to remove the screws hidden behind the seal.

At this very moment you have the opportunity to unblock the opening holes of the sunroof enjoy reading this article I realized on the subject.

https://velumautostore.com/comment-deboucher-les-tuyaux-evacuation-du-toit-ouvrant-vw-audi/

20 – Lift the rear glass

Normally there is the possibility of sliding it a little forward or you can remove it supplement.

21 – Remove supports in the corner

This place above the sunroof by standing by the door studs or by the location of the rear window.

Remove the media that make the angle (screw torx) the media are clips and targeted. WARNING to the seal (3).
Do the same both sides Der-cliper slide supports (1) by disassembling it up Remove the slide supports from the finishing bar (2)

22 – Remove the screws from the coiling rack holder set.

Remove the spotted screws (1) to gently remove the blind holder backwards and then, once the support is removed, remove the finishing bar from the blind by dragging it sideways.

23 – Setting up the new panoramic sunroof store

This is the most minute part of the sunshade’s panoramic sunroof replacement.

Put the new sunshade >>available here< in the support and slide the metal finishing bar into the black rubber part (1), trying to center it as possible
Think about putting the small staples (2) that I provided for free with the blind.
They remove from the plastic part by pushing with a small flat screwdriver.

The staples hardly fit very difficult to see in the notch of the lateral spring provided for this purpose, do not file them, saw them … it comes back hard and it’s normal.
Skew it to engage it and then hand the right, it can force to put it straight but no impact on the assembly.

24 – Engage the coiling support store set

Solution 1: Engage the flat part of the sunshade’s panoramic sunroof into the rail (1) on each side to revise the screws removed at stage 19.

Solution 2: Engage only the store-finishing bar set alone and then move on to step 23 (addition of slide racks).
Add the coiling blind holder, once the blind is installed)

25 – Add slide racks

Add the slide racks (2) by engaging them in the finishing bar (3) laterally, then clipping them over the top on the clip in reverse to step 19.

Reassemble the corner supports above the sunroof
WARNING grease only in the hollow part of the slide holder photo (to put).

26 – Manually operate the panoramic sunroof blind manually to make sure the blind doesn’t hang

Using a 6-panel key directly on the winding blind engine (spotted 3 ) which is located at the back just behind the coiling store support set.
The ideal being to make a few go back before seeing if there is a possible blockage (dirt, debris in the guide rail) and that everything goes well.

27 – Rise roof sky mold inversely to stage 7

28 – Reassemble rear window of sunroof fixed part by proceeding inversely to step 15

29 – Putting key tension on the
contact ‘> contacting ‘> battery delivery

We put the battery back after putting the ignition to avoid being in the car at the time of the contact to avoid being knocked out by the airbags in case of malfunction (we are never safe).

28 – TOP calibration – STORE

After sunshade’s panoramic sunroof replacement, you must reset his engine.

If the contact is not yet set then put the battery contact off and put the battery back it can avoid getting an airbag in the head and if there is a malfunction.
At least by doing it like that you’re out there.

1 RESET PANORAMIC SUNROOF

Put Rotating button in maintenance position.
Pull down glass button down and hold for 20 seconds even when it is moving it will open and close you can release

2 RESET SUNSHADE’S PANORAMIC SUNROOF

Store must be in closed position.
Press and hold on « close » store for 20 seconds.
The blind opens and closes then you can release.

test

If the blind works properly, you can go back in the opposite direction otherwise review what is wrong and be methodical you will quickly find the cause of the problem.

Congratulations your sunshade’s panoramic sunroof replacement is done.

An article is available on the subject (useful after changing the sunroof blind):

Réinitialiser les moteurs du toit ouvrant panoramique VW et du Store.

If you have any questions here is my contact: velum.auto.store@gmail.com

To get this TUTO PDF
for sunshade’s panoramic sunroof replacement enter your email address here: