Sunshade’s panoramic sunroof replacement VW Audi Skoda Seat

Torn store? Relaxed? musty, dampness on the canvas? The spring is out of side guides?
We’ll see how to make sunshade’s panoramic sunroof replacement on VW Tiguan, Touran, Sharan, Golf V break, Audi Q5, Skoda Superb break, Skoda Yeti and Seat Leon break.
This is not given in concession because there is quite a labor the bill can easily go up to around 700 or even much more.
It is a method that works, it is not the only one but i will give you all you need for sunshade’s panoramic sunroof replacement.

SAFETY – PRECAUTION

I do not accept any responsibility in case of a personal accident or deterioration of your vehicle, take the necessary precautions and check not to have anything broken or damaged, if this is the case then change what has been damaged before going back up.
Check the electrical cables, some are used to power the airbags so do not laugh with the safety organs.

Tools

  • Torx T15 T20 T25 key/turntable or tip
  • 10 key or tip (depending on model)
  • Big flat screwdriver
  • Dismantling tool available here (optional)
  • Plastic dismantling tools to avoid scratches on the interiors of your car. Failing that, an old loyalty card, a guitar metronome etc…
  • 6-pans key set or tip
  • New Sunshade you can find >> here

Time

3/4H ENVIRON

A Note: there may be some difference in the levels of dismantling of the amounts according to the models and according to the vehicles below

VW TIGUAN, SHARAN, TOURAN, JETTA, GOLF VARIANT, AUDI Q5, SKODA YETI.
Example: for the Golf variant there is the trunk part to disassemble in addition and the maintenance of the roof sky is different I voluntarily omitted it because this car is rare. anyway you have enough information to carry out the change of the sunroof blind, sunroof curtain, velum.

1 – Open the sunroof in “maintenance position”

Open the TOP in maintenance position, if you don’t know how to do it you can read the article that features the VW panoramic sunroof by clicking here

Knob

the important thing is to have access to the screw you see (position beyond the max)

maintenance position - changing the panoramic sunroof blind
maintenance position
access to screws - changing the panoramic sunroof blind
access to screws

2 – Open the sunroof blind to the maximum

open the blind to the maximun

4 – Disconnect the battery

As a safety precaution, it is advisable to disconnect the battery.

5 – Place ceiling lights and plastic caches

deciting

Remove the plastic part using a pick and then remove the screws.

6 – Remove side mount front left

Remove the AIRBAG symbol with the thinnest plastic tooling possible (pick) by leveraging by putting pressure on the shapes (see arrows inwards).
Do the same for the right front amount.

left front climb - changing the panoramic sunroof blind
Rising front left

7 – Remove left center mount

You must start by removing the AIRBAG symbol as previously remove the fastening screw (put the belt setting high enough but not too high in order to be able to access with the torx screwdriver).

The amount must be detached from the lower dwellings in order to be able to bring it down (try not to take out the plastic part that serves as a setting for the height of the belt).
Do the same for the right.

left center mount - change of panoramic sunroof blind
central side climb

8 – Remove the profile that goes around the roof sky

There are about twenty staples to de-clip by leveraging with a plastic disassembly tool (failing that you can use a blue card for example or a pick).

9 – Remove sunscreen

Open small caches with an extra fine plastic tool or a precision screwdriver but with caution, an extra fine guitar pick can do the trick.

sunscreen - change of panoramic sunroof blind
Sdr

Be careful with the sundness because it still holds by its cables so you have to remove the plug so that it is finally free.

10 – Remove the tailgate back cover (chest)

rear cover - changing the panoramic sunroof blind
back cover

Open the tailgate and pull down the back cover with a snap.

11 – Remove the back cover (chest)

Remove plastic pushers with a special T10236 tool or with pliers on either side of the plastic part.

low rear cover - changing the panoramic sunroof blind

Remove the plastic part from the metal hoops then remove it upwards.

12 – Remove side cover (chest)

safe-hide-lateral - change of panoramic sunroof blind
Dav

Motto the screws of the fasteners of the side part of the trunk then unseal the peripheral parts by passing the hands or a tool between the joint and the plastic.

13 – Remove top side cover (chest)

Remove the dressing piece by pulling down.

top side cover - change of panoramic sunroof blind
Dav

Shoot following arrows A and then B.

14 – Fold the back seat, advance the seats to the max and lower the seats

13 – Unplug plugs controls sunroof

connectivity - changing the panoramic sunroof blind
Connection

14 – Remove plastic holding parts from roof sky

Remove the screws from the plastic part.

15 – Remove the handles

Take the handle as if you wanted to catch it remove the 2 torx screws.

Note: On Q5 these are plastic parts to remove instead of a special tooling that you can >> find here< mais un pic a brochette plié avec le bon angle peut faire l’affaire.

16 – Check that nothing holds the roof sky, light, ceiling light then extract the roof sky mold by advancing it forward in order to clear it from the rear studs and then extract the roof sky molded from the rear

17 – Remove the rear window from the sunroof

Deflect the screws (torx T25) from the top, paying attention to the 2 or 1 washers depending on the thickness of the washer that are on top.

If this is not already done, the mobile part of the sunroof should be brought back to the open position max. (by reconnecting the connector)

access to screws

If you have to operate the sunroof you can do it manually with a 6-panel key directly on the sunroof engine in front

Lift the seal with your hands to pass the screwdriver to remove the screws hidden behind the seal.

At this very moment you have the opportunity to unblock the opening holes of the sunroof enjoy reading this article I realized on the subject.

https://velumautostore.com/comment-deboucher-les-tuyaux-evacuation-du-toit-ouvrant-vw-audi/
useful link

18 – Lift the rear glass

Normally there is the possibility of sliding it a little forward or you can remove it supplement.

19 – Remove supports in the corner

This place above the sunroof by standing by the door studs or by the location of the rear window.

Dav

Remove the media that make the angle (screw torx) the media are clips and targeted. WARNING to the seal (3).
Do the same both sides Der-cliper slide supports (1) by disassembling it up Remove the slide supports from the finishing bar (2)

20 – Remove the screws from the coiling rack holder set.

Remove the spotted screws (1) to gently remove the blind holder backwards and then, once the support is removed, remove the finishing bar from the blind by dragging it sideways.

21 – Setting up the new panoramic sunroof store

This is the most minute part of the sunshade’s panoramic sunroof replacement.

Put the new sunshade >>available here< in the support and slide the metal finishing bar into the black rubber part (1), trying to center it as possible
Think about putting the small staples (2) that I provided for free with the blind.
They remove from the plastic part by pushing with a small flat screwdriver.

Dav

The staples hardly fit very difficult to see in the notch of the lateral spring provided for this purpose, do not file them, saw them … it comes back hard and it’s normal.
Skew it to engage it and then hand the right, it can force to put it straight but no impact on the assembly.

22 – Engage the coiling support store set

Dav

Solution 1: Engage the flat part of the sunshade’s panoramic sunroof into the rail (1) on each side to revise the screws removed at stage 19.

Solution 2: Engage only the store-finishing bar set alone and then move on to step 23 (addition of slide racks).
Add the coiling blind holder, once the blind is installed)

23 – Add slide racks

Add the slide racks (2) by engaging them in the finishing bar (3) laterally, then clipping them over the top on the clip in reverse to step 19.

mounting the blind - changing panoramic roof blind
assembly

Reassemble the corner supports above the sunroof
WARNING grease only in the hollow part of the slide holder photo (to put).

24 – Manually operate the panoramic sunroof blind manually to make sure the blind doesn’t hang

Using a 6-panel key directly on the winding blind engine (spotted 3 ) which is located at the back just behind the coiling store support set.
The ideal being to make a few go back before seeing if there is a possible blockage (dirt, debris in the guide rail) and that everything goes well.

25 – Rise roof sky mold inversely to stage 7

26 – Reassemble rear window of sunroof fixed part by proceeding inversely to step 15

27 – Putting key tension on the
contact ‘> contacting ‘> battery delivery

We put the battery back after putting the ignition to avoid being in the car at the time of the contact to avoid being knocked out by the airbags in case of malfunction (we are never safe).

28 – TOP calibration – STORE

After sunshade’s panoramic sunroof replacement, you must reset his engine.

If the contact is not yet set then put the battery contact off and put the battery back it can avoid getting an airbag in the head and if there is a malfunction.
At least by doing it like that you’re out there.

1 RESET PANORAMIC SUNROOF

Put Rotating button in maintenance position.
Pull down glass button down and hold for 20 seconds even when it is moving it will open and close you can release

2 RESET SUNSHADE’S PANORAMIC SUNROOF

Store must be in closed position.
Press and hold on “close” store for 20 seconds.
The blind opens and closes then you can release.

test

If the blind works properly, you can go back in the opposite direction otherwise review what is wrong and be methodical you will quickly find the cause of the problem.

Congratulations your sunshade’s panoramic sunroof replacement is done.

An article is available on the subject (useful after changing the sunroof blind):

https://velumautostore.com/reinitialiser-les-moteurs-du-toit-ouvrant-panoramique-et-du-store-vw-audi/
useful link

If you have any questions here is my contact: velum.auto.store@gmail.com

To get this TUTO PDF
for sunshade’s panoramic sunroof replacement enter your email address here:

Contact via Facebook !
Click Here to Leave a Comment Below

Leave a Comment:

Rejoindre la liste d'attente Nous vous informerons lorsque le produit sera en stock. Veuillez laisser votre adresse e-mail valide ci-dessous.